< Previous310SoilsEnvironmental TestingCombination ManifoldProduct Code: 532-136tel: +44 (0)1525 249 200 • email: ele@eleint.co.uk • www.ele.comThis is required to regulate gas pressure source in pressure plate extraction systems. There are 3 types available to cover all requirements and they enable precise control of pressure. Pressure manifolds are an essential component in pressure plate extraction systems. They are required to control the air pressure, from a compressor or compressed air vessel, into the extractor. ELE can supply three different types to cover all requirements; low pressure manifold, for 0-5 bar systems, low to high pressure manifold, for 1-15 bar systems, combination manifold, for both 0-5 and 1-15 bar systems running in parallel. The combination manifold combines both the low pressure and low to high pressure manifolds.SpecificationsDimensions (mm)939 x 452 x 330Pressure Range1 to 75 psiWeight (kg)12.7PM Compressor 220-240 V AC, 50 Hz, 1 phProduct Code: 532-180/01Ideal for pressure plate extraction systems. Electrically powered and fully accredited. Conforms to EC Directive 98/37/CE. This unit provides compressed air for all ELE’s pressure plate apparatus. The compressor is designed for sustained, continuous operation and provides up to 20 bar operating pressure. These compressors are compact and can be transported easily by one person. The compressor consists of a motor and block, which is cast in one piece. This improves heat dissipation considerably. Pistons, piston rings, con-rod, bearings and crank flange have been designed with efficiency and durability in mind. Valves in the compressor block are machined in non-corrosive Stainless Steel and the valve reeds are fitted with heat dissipating lift limiters. This ensures air-tight valves and longer life. The robust electric motor features strengthened bearings and a generously-sized winding which lengthens motor life considerably. The motors start without problem even if the supply voltage is low. Every compressor is filled with special temperature resistant, top performance lubricating fluid. The result is almost no oil carbon deposits on the valves. This compressor must be used in conjunction with a manifold assembly if intended for use in pressure plate extraction systems.SpecificationsMax Gauge Working Pressure20 barDimensions (mm)525 x 260 x 430Air Receiver Capacity (ltrs)4Highest Sound Pressure Value75 dB when tested to DIN 45635Theoretical Inlet Capacity160 l/ minFree Air Delivered20 bar (at 8 bar working pressure)No. of Cylinders1Oil Capacity (ltrs)0.13Oil Top-Up Qty (ltrs)0.05Max Mains Fusing (slowblow or gl glass)16 ampMax Rated Current6.2 ampRated Power (kW)1.1Rated Speed (rpm)2850Protection ClassIP54Max Cut-in Frequency30 times / hourWeight (kg)29.5Accessories:Connection Set for 532-180 series (532-182)311SoilsEnvironmental TestingConnection Set for 532-180 SeriesProduct Code: 532-182Ceramic Cup 15 BarProduct Code: 532-124Used to calibrate all types of electrical moisture measuring blocks. The Cup Extractors are (83 mm) 3-1/4 inch overall height by (64 mm) 2-1/2 inch outside diameter and will fit into the 532-120 and 532-100 extractors. Inside cup dimensions are (45 mm) 1-3/4 inch diameter by (51 mm) 2 inch deep.SpecificationsOuter Dia (mm)61Inner Dia (mm)44.7Outer Height (mm)81.3Interior Height (mm)56.1Electrical Lead ThroughProduct Code: 532-126This Stainless Steel 1/4 NPT fitting leads through 10 electrical wires (26 AWG), connected to the fitting with epoxy seal. Handles up to 300 PSI.SpecificationsDimensions (mm)77 x 77 x 25.4Weight (kg)0.03Outflow Tube Assembly with SealProduct Code: 532-120/14Plug Bolts with SealProduct Code: 532-120/16Set of 5.Right Angle Outflow Adaptor KitProduct Code: 532-120/12Set of 4.www.ele.com • email: ele@eleint.co.uk • tel: +44 (0)1525 249 200312WaterEnvironmental TestingWater Level MeasurementWater Level IndicatorsWater Level Indicator (Dipmeter) with Audio & Light IndicatorProduct Codes: 450-008, 450-010, 450-011, 450-012, 450-013, 450-015, 450-017tel: +44 (0)1525 249 200 • email: ele@eleint.co.uk • www.ele.comPortable, lightweight, simple, reliable and easy to operate. Clear interval markings. Audible and visual water level alert signals. Dipmeters are portable instruments for measuring the water level in wells, standpipes and boreholes. They are simple to use, portable and can be used at many locations. The tape design prevents it from sticking to wet surfaces, such as the lining of a borehole, ensuring accurate measurements. The dipmeters have a Stainless Steel probe fitted to a flexible graduated cable which is wound onto a hand reel containing a transistorised switched circuit, audio (buzzer) and visual (LED light) indicators and a battery. Sensitivity adjustment for variations in water conductivity, non-stretch polyethene coated steel tape. The sensor probe incorporates an insulating gap which acts as a switch, the circuit being completed when contact is made with the water. The cable consists of non-stretch contoured tape with standard steel conductors, graduated at one millimetre intervals. The probe is lowered down a borehole on the end of the tape. When it makes contact with water a buzzer sounds and an LED light comes on, both located on the reel. A reading can then be taken from the tape at the top of the borehole to indicate the water depth. A sensitivity control is accessible inside the hand reel to enable adjustment to suit the water conductivity.Available Lengths:See Specifications table below.Further Information:Graduated every 10 mm.SpecificationsIndicatorAudio and visualTape Graduationm/cm/mmProduct CodeTape Length (m)Weight (kg)450-008301.7450-010502.0450-0111003.0450-0121503.8450-0132004.6450-0153007450-01750011.5313WaterEnvironmental TestingWater & Sediment SamplingWater SamplersWater samplers fall into 3 main categories: those which collect an heterogeneous sample from, at, or just below the water surface; those which collect a sample from a specific depth in still water; and those which collect a mid-stream sample from a river, stream or irrigation channel. The ELE selection of samplers covers all applications.Tube Water SamplerProduct Code: 520-200To collect up to 250 ml. Complete with Stainless Steel measuring tape with grip and eye (20 metres).Water Trap SamplerProduct Code: 520-215This sampler is designed to be used in a flowing river or stream at any desired depth to 25 metres. The design is such that the open ends through which the water flows can be simultaneously closed, thus retaining the 1250 ml sample which may then be raised to the surface. The accessories include a hand winch, 25 metres of steel wire and a depth meter. The complete set is contained in a wooden transport case with padlock.Further Information:Case dimensions: 700 x 370 x 270 mmwww.ele.com • email: ele@eleint.co.uk • tel: +44 (0)1525 249 200Combination Sampling & Measuring OutfitProduct Code: 521-020With colour scale, water sampling bottle, plankton net, bottom sampling dredge, sounding lead and calibrated line, 20 metres long marked at 1 and 5 metre intervals, armoured thermometer and Secchi disc (for turbidity check).Further Information:Supplied with carrying case.Flow MeasurementFlow MetersThe method used for measuring the rate of a particular flow is determined by the course rate of flow and by the nature of the flow channel. The ELE range therefore encompasses equipment for measuring the faster flows encountered in rivers and streams, down to the low rates occurring during run-off from field drains.Miniature Current Flow Meter Wading SetProduct Code: 520-265For velocities 0.025 up to 5.0 metres/second. Consisting of current meter, revolution counter, wading rods, base and knob, 3 metre wading cable.Further Information:Complete with carrying case 850 x 180 x 220 mm.SpecificationsVelocity Range (m/s)0.025 to 5Accessories:PC Download Cable for Current Flow Meter (520-261)314WaterEnvironmental TestingLarge Current Flow Meter Wading SetProduct Code: 520-260tel: +44 (0)1525 249 200 • email: ele@eleint.co.uk • www.ele.comConsisting of current meter, revolution counter, wading rods, base and knob, 3 metre wading cable.Further Information:Complete with carrying case 850 x 180 x 220 mm.SpecificationsVelocity Range (m/s)0.025 to 10Gauging Weirs & FlumesWater is a precious agricultural resource. Careful monitoring is essential to ensure that it is used as effectively as possible. The comprehensive range of equipment offered has been specifically designed to measure or estimate the mass flow in both natural, or man-made, irrigation and drainage channels.Parshall Flume (Small)Product Code: 520-360Having a throat width of 25 mm for flows 0.3 to 5 litres/second.Further Information:Overall dimensions 710 x 360 x 270 mm.Parshall Flume (Large)Product Code: 520-365Having a throat width of 50 mm for flows 0.5 to 14 litres/second.Further Information:Overall dimensions 860 x 420 x 305 mm.WSC Flume (Small)Product Code: 520-375For flows 0.1 to 2 litres/second.Further Information:Overall dimensions 500 x 250 x 175 mm.315WaterEnvironmental TestingWSC Flume (Large)Product Code: 520-380For flows 1 to 7.5 litres/second.Further Information:Overall dimensions 780 x 350 x 230 mm.Weir Plate Set with Weir Plate Carrier & Four Interchangeable Weir PlatesProduct Code: 520-3901200 mm wide x 750 mm high x 5 mm thick.www.ele.com • email: ele@eleint.co.uk • tel: +44 (0)1525 249 200Simple Cut-Throat FlumeProduct Code: 520-345Throat width 100 mm, for measuring flows in the range 0 to 15 litres/second.Water Quality TestingComparator ReagentsWhere only a few chemical tests need to be done, and accuracy is less important, it is cost-effective to use a colour comparator. These units can be used to perform the following tests: Ammonia, Chlorine, Iron, Nitrate, Manganese and pH.Chlorine Starter Pack including Colour Disk & Reagents. Sufficient for 50 Tests.Product Code: 432-032SpecificationsMeasurement Range (mg/l)0-5.0Chlorine Reagent Pack for Comparator. Sufficient for 250 Tests.Product Code: 432-032/10SpecificationsMeasurement Range (mg/l)0-5.0316WaterEnvironmental TestingPaqualab Standard SystemsThe two Paqualab systems are designed so that all the necessary equipment to determine the physical, chemical and microbiological parameters can be stored in one easily carried case. Results are obtained within 16 hours. The numerical results have precision and reproducibility. The method is simple and economical, enabling regular analysis to be carried out. This technique is accepted worldwide and Paqualabs are used in over 50 countries. Reusable components can be sterilised in the field. Consumables are pre-sterilised and have a long shelf life. Sample deterioration through transport and handling is eliminated.Paqualab System 50 & 25 for Analysis of Drinking Water to EC Standard Categories 1 & 2Product Codes: 418-160, 418-150tel: +44 (0)1525 249 200 • email: ele@eleint.co.uk • www.ele.com317WaterEnvironmental TestingPortable drinking water quality testing system. Microbiological - Coliform and E.Coli. Physical - temperature, conductivity and turbidity. Chemical - pH, CI, NH3, NO2 and NO3 plus over 40 chemical tests available. AC/DC and rechargeable battery powered incubator. On-site testing for fast, accurate results. Long-term monitoring and emergency testing of drinking water to EC and WHO guidelines. Comprising of the ELE Paqualab incubator 25 and 50, pH/temperature/mV meter, conductivity/temperature meter, turbidity meter, 0-1000 FTU, ELE Paqualab photometer, and consumables for 200 tests on faecal or total coliforms, chlorine, ammonia, nitrates and nitrites. The Paqualab is a portable testing system for the key drinking water quality parameters. The Paqualab allows the laboratory to be carried to water so that accurate results are obtained sooner, even in remote areas. Laboratory standard results can be obtained by operators with the minimum of training.The equipment provided in each Paqualab has been specifically designed for field use. Aluminium replaces glass for many components for improved strength and lighter weight. The incubators have 2 pre-set temperatures that are usually set to 37°C and 44°C. The internal battery provides sufficient power for a full incubation cycle. Over 1000 Paqualabs are in use throughout the world for monitoring drinking water in remote areas, emergency situations, research and education. The Paqualab is a completely modular system. Standard kits are available as shown below. All items are also available individually to enable the user to build a system to meet their specific requirements. In addition, Paqualab Incubator systems contain all the hardware required for microbiological tests. Paqualab standard systems are based on the Incubator systems and also include tests for other parameters as shown below.Further Information:418-150: Overall dimensions 335 x 230 x 275 mm418-160: Overall dimensions 475 x 230 x 275 mmStandard System5025Item SuppliedProduct Code418-160418-150(420-035) Universal and Incubator 50Yes-(420-030) Universal Incubator 25-Yes(430-020) pH/Temp/mV Meter YesYes(513-160) Conductivity/TDSTemp MeterYesYes(430-260) Turbidity Meter YesYes(430-550) PhotometerYesYes(433-115/10) Chlorine Reagent System, Free, Total. Pack sufficient for 250 tests.YesYes(433-102/10) Ammonia Reagent System, Pack sufficient for 250 tests.YesYes(433-166/10) Nitrate Reagent System, Pack sufficient for 200 tests.YesYes(433-168/10) Nitrite Reagent System, 4 Packs of 50 tests.YesYes(422-010) Coliform Starter Pack sufficient for 200 tests.YesYesSpares/Consumables:Aluminium Petri Dishes (Pack of 25) (422-560)Coliform Starter Pack, sufficient for 200 Tests (422-010)Filtration Unit Aluminium Construction complete with Sampling Cup (420-450)Membrane Lauryl Sulphate Medium 38.1 g Pack sufficient for 200 Tests (422-110)Pad Dispenser (422-515)Sterile Filter Membranes and Absorbent Pads (Pack of 200) (422-508)www.ele.com • email: ele@eleint.co.uk • tel: +44 (0)1525 249 200318WaterEnvironmental TestingPaqualab Portable Incubators & Filtration UnitThe ELE Paqualab incubators are fully portable which enables microbiological water analysis to be carried out in remote locations which lack normal laboratory facilities. Various power supply options are available including internal rechargeable batteries or an external 12 V DC, 24 V DC, 110 V AC, or 240 V AC supply. This flexibility means that samples can be incubated on-site, in a car or in a laboratory thereby producing accurate results in the shortest possible time.Paqualab Incubator 50:- Dual Incubator Filtration Unit 50 Aluminium Petri Dishes & Paqualab Incubator 25:- Single Incubator Filtration Unit 25 Aluminium Petri DishesProduct Code: 420-035, 420-030tel: +44 (0)1525 249 200 • email: ele@eleint.co.uk • www.ele.com319WaterEnvironmental TestingThe ELE Paqualab 50 includes two incubators - the standard and universal (each with 2 pre-set temperatures, normally 37°C and 44°C), a membrane filtration unit, microbiological accessories kit, connecting cables and operating manual. All components are housed in a convenient rigid carrying case which can also accommodate a number of electronic meters from the ELE Paqualab range.The ELE Paqualab 25 includes a universal incubator with 2 pre-set temperatures (normally 37°C and 44°C), a membrane filtration kit, connecting cables and operating manual. All components are housed in a convenient rigid carrying case which can also accommodate a number of electronic meters from the ELE Paqualab range.Further Information:The system will operate on 12 V or 24 V DC, 110 V or 240 V AC, or the internal 12 V rechargeable battery supplied.Spares/Consumables:Filtration Unit, aluminium construction complete with Sampling Cup (420-450)Incubator System5025Item SuppliedProduct Code420-035420-030Large Rigid Carrying CaseYes-Standard Rigid Carrying Case-YesUniversal IncubatorYesYesStandard IncubatorYes-Incubator Linking LeadYes-Filtration UnitYesYesMains LeadYesYesBattery LeadYesYesCigar Lighter PlugYesYesAluminium Petri DishesYesYesPlastic Autoclavable Bottles (x4)YesYesDropping Pipettes (x2)YesYesForcepsYesYesMagnifying GlassYesYesThermometer (Spirit)YesYesTrim ToolYesYesGreaseYesYesInstruction Manual in BinderYesYeswww.ele.com • email: ele@eleint.co.uk • tel: +44 (0)1525 249 200Filtration Unit, aluminium construction complete with Sampling CupProduct Code: 420-450 ±Anodised Aluminium Membrane Filtration Unit. ±Light compact and field sterilisable. ±Fits together for storage into a size of 120 mm high x 80 mm diameter. ±Supplied with sampling cup and nylon cord. ±Filtration unit graduated with 50 ml and 100 ml levels. ±Supplied with hand-operated suction pump.Spares/Consumables:Spare Parts Kit for Filtration Unit (420-451)Membrane Filtration Unit Spare Parts KitProduct Code: 420-451For Filtration Unit (filter disc, gasket kit and 0-ring).Next >