< Previoustel: +44 (0)1525 249 200 • email: ele@eleint.co.uk • www.ele.com230Design & Testing of Bituminous MixturesAsphaltManual CompactionCompaction MouldProduct Code: 45-6310Product Standards:EN 12697-30, BS598-107, ASTM D6926, AASHTO T245Compaction Mould comprising of mould body, baseplate and combined filling/extraction collar.SpecificationsWeight (kg)3.5Spares/Consumables:Compaction Mould Body (45-6310/10)Baseplate (45-6310/11)Filling/Extraction Collar (45-6310/12)Compaction HammerProduct Code: 45-6460Compaction PedestalProduct Code: 45-6410Product Standards:EN 12697-30, BS 598-107Comprising a 300 mm2 x 25 mm thick steel plate complete with 4 tie rods and securing nuts. A mould clamp and hammer guide are fitted to the plate. The unit is supplied complete with a laminated hardwood block.SpecificationsWeight (kg)40Product Standards:EN 12697-30, BS 598-107, ASTM D6926, AASHTO T245Satisfies BS 598. The hammer has a 4535 g sliding weight with a free fall of 457 mm.SpecificationsDrop18 inches (457 mm)Tamping Face3-7/8 inches (98 mm) diaHammer10 lb (4.54 kg)ConstructionMachined steel; cast aluminium handleWeight (kg)7.85www.ele.com • email: ele@eleint.co.uk • tel: +44 (0)1525 249 200231Design & Testing of Bituminous MixturesAsphaltManual & Automatic Compaction AccessoriesHeating Bath 30 LitreProduct Code: 45-6550/01Product Standards:BS 598-107, EN 12697-30Water Bath with LED display, cover and internal perforated shelf. Temperature range ambient to 60°C ± 5°C. For 220–240 V AC, 50-60 Hz, 1 ph.Will hold up to 12 Marshall Samples.Proctor/Core Cutter ExtruderProduct Code: 23-4200Product Standards:BS 598-107, BS 1377-1, EN 12697-30Paper DiscsProduct Code: 45-6462Product Standards:BS 598-107, EN 12697-30Non-absorbent, 99 mm diameter - Pack of 100.Steel BlockProduct Code: 45-6463Product Standards:BS 598-107, EN 12697-30100 mm diameter x 50 mm height. For heating the compaction hammer foot. Weight 3 kg.tel: +44 (0)1525 249 200 • email: ele@eleint.co.uk • www.ele.com232Design & Testing of Bituminous MixturesAsphaltMarshall Stability & FlowThe accurate measurement of stability and flow of specimens tested in a load frame is important if consistent and representative results are to be achieved. The load frames and ancillary items listed have been designed to enable technicians to test specimens quickly and easily with confident recording of results.Marshall Load FramesMultiPlex 50 Load FrameProduct Code: 25-3700/01Product Standards:MarshallEN 12697-34, EN 12697-12, EN 12697-23, BS 598-107, ASTM D6927, ASTM D6931CBREN 13286-47, BS 1377-4, ASTM D1883, AASHTO T193TriaxialBS 1377-7, BS 1377-8, ASTM D2166/D2166M, ASTM D2850, ASTM D4767, ASTM D7181, AASHTO T208, AASHTO T296, AASHTO T297Compact bench mounting load frame designed for performing laboratory CBR, unconfined compression, consolidated drained, consolidated undrained and Marshall Stability tests. Has a variable speed of 0.5 to 50.8 mm per minute and features rapid approach of platen.SpecificationsCBR PenetrationYesUnconfined CompressionYesConsolidated UndrainedYesConsolidated DrainedYesMarshall Stability and FlowYesPower Supply220-240 V AC, 50-60 Hz, 1 phDimensions L x W x H (mm)550 x 400 x 1470Max Vertical Clearance (mm)800Horizontal Clearance (mm)265Platen dia (mm)133Platen Travel (mm)100Platen Speed Range0.5 to 50.8 mm/minRapid Approach Speed40 mm/minWeight (kg)100 (shipping 113 kg)Spares Kit for MultiPlex 50 Load FrameProduct CodeProduct25-3700/K1Spares kit for MultiPlex 50 Load Framewww.ele.com • email: ele@eleint.co.uk • tel: +44 (0)1525 249 200233Design & Testing of Bituminous MixturesAsphaltMarshall Test 50Product Codes: 45-6810/01, 45-6810/06Product Standards:EN 12697-34, EN 12697-12, EN 12697-23, BS 598-107, ASTM D6927, ASTM D6931This bench-mounting mechanical load frame is ruggedly constructed to encompass the strain and loads involved with the test. The unit is compact in size and can be quickly installed on a bench top, requiring only a power point. It has been designed for simple operation, is easy to clean and requires minimal maintenance. ±Geared screwjack and motor drive. ±Precise speed. ±Internal limit switch for both directions of travel. ±Easy to use controls.Further Information:Load frame, 50 kN capacity. Supplied without breaking head. For 220-240 V AC, 50 Hz, 1 ph.SpecificationsMarshall Stability and FlowYesProduct CodePower Supply45-6810/01220-240 V AC, 50 Hz, 1 ph45-6810/06220-240 V AC, 60 Hz, 1 phSpares/Consumables:Jack Sleeve (1871B0045)Jack Screw (1729B0032)Nut (1274A0017)Worm Gear (1274B0014)Spares Kit (45-6810/K)Marshall test AccessoriesProduct CodeProduct45-6850Breaking Head Stability Mould45-6880Flow Meter BS/EN45-6890Flow Meter ASTM78-0860Clamped Boss Load Ring 50 kN47-0202Digital Thermometer -50 to +1000°C47-0202/10Asphalt Needle Probe45-6550/0130 ltrs Heating Bath27-1559S-Type Load Cell 50 kN45-6860Lottman Breaking HeadBreaking Head Stability MouldProduct Code: 45-6850Product Standards:BS 598Electronic InstrumentationFlow TransducerProduct Code: 45-6820/11Product Standards:EN 12697-34, ASTM D6927-15S-Type Load Cell 50 kNProduct Code: 27-1559Product Standards: EN 12697-34Maximum working capacity of 50 kN and excitation 10 V AC/DC with an output of 2.7 mV/V nominal. Aluminium alloy and Stainless Steel construction with IP65 environmental protection. Fitted with 5-pin DIN plug.SpecificationsValue of CBR %ALLEnvironmental ProtectionIP65Force Capacity (kN)50tel: +44 (0)1525 249 200 • email: ele@eleint.co.uk • www.ele.com234Design & Testing of Bituminous MixturesAsphaltDSU Electronic Readout & Control SystemProduct Codes: 27-1300/01, 27-1300/02The Data System Unit (DSU) is a versatile instrument designed to accommodate the general logging requirements of geotechnical and materials testing engineers. Its intelligent interface allows the user to work with a range of different sensors. ±4 channel automatic control and data-logging unit. ±Automatic, dual-frame control. ±Performs CBR, Marshall, unconfined compression, direct and residual shear, one-dimensional consolidation and unconsolidated undrained tests. ±LAN connection - software can be running anywhere on your server. ±Never lose data from power failures. ±2 GB of non-volatile memory. ±Extended warranty.Features:The DSU has two distinct modes of operation; DS mode (Data System) and DU Mode, for operation with ELE International’s established DS7 geotechnical testing software where the unit can be used as a stand-alone device without PC connection.DS Mode: ±Up to four one dimensional consolidation tests. ±Up to two CBR tests. ±One direct/residual shear test. ±One triaxial quick un-drained test.DU Mode: ±Up to two Marshall tests. ±Up to two CBR tests. ±Up to two unconfined compression tests. ±Automatic frame control.Overview: ±Touch Screen data entry for stand-alone operation, Marshall/CBR/quick un-drained. ±Automatic single and dual frame control (with multiplex 50 frame). ±Log memory of 2 GB. ±Non-volatile memory. ±Ethernet TCPIP link and serial comms support. ±Market leading signal stability. ±Certificate and manual calibration features. ±Comes with 27-1510 RS232/USB cable. ±Comes with 27-1300/11 cable, safety/10. ±Comes with 27-1300/12 PC cable.SpecificationsProduct CodePower Supply27-1300/01220-240 V AC, 50-60 Hz, 1 ph27-1300/02100-120 V AC, 60 Hz, 1 phAccessories:Dual Frame Comms Cable (27-1300/10)www.ele.com • email: ele@eleint.co.uk • tel: +44 (0)1525 249 200235Design & Testing of Bituminous MixturesAsphaltDuctility Testing MachineProduct Code: 46-4120Product Standards:EN 13398, ASTM D113, ASTM D6084, AA SHTO T51, EN 13589, EN 13703, AASHTO T300.The Ductility Testing Machine is used to determine the ductility of bituminous materials in a briquette mould by measuring the breaking elongation at a constant speed of 50 mm/min. It is designed for testing 3 specimens simultaneously. The internal tank is made of Stainless Steel. The bath is fitted with an immersion heater in order to obtain (in normal conditions) the 25°C test temperature.SpecificationsDimensions L x W x H (mm)300 x 1850 x 550Capacity3 specimensWeight (kg)80Watts (W)1000Power Supply220 V AC, 50-60 Hz, 1 phLoad3 x max 300 N Load CellsAccuracy± 0.1 NFeatures:The Ductility Testing Machine comprises a speed control and water circulator to maintain the homogeneous water temperature. ±Elongation measurement through the motor encoder. ±3 simultaneous load measurements with 18-bit resolution. ±Speed control with servo AC motor between 0.01 to 100 mm/min. ±Ethernet connection for computer interface. ±Has 3 load cells with an accuracy of ± 0.1 N, with a maximum capacity of 300 N. ±Failure conditions can be downloaded to the unit. ±Cooling unit. ±Automatic control and data acquisition.Accessories:Briquette Mould ASTM/AASHTO (46-4120/10)Base Plate for Briquette Mould (46-4120/11)tel: +44 (0)1525 249 200 • email: ele@eleint.co.uk • www.ele.com236Specific GravityAsphaltVacuum Pyknometer ApparatusProduct Code: 45-9305/01Product Standards:EN 12697-5, ASTM D2041/D2041M, AASHTO T209The Vacuum Pyknometer is a large capacity unit used in the Rice Test for determining the maximum specific gravity of bituminous paving mixtures. The Pyknometer has a total volume of approximately 10 litres and will conveniently accept samples of 6000 g to minimise segregation effects. The unit is constructed of lightweight polycarbonate, with the upper half being transparent for visual observation of the effects of the vacuum. The Vacuum Pyknometer Apparatus consists of a 6000 g pyknometer, vacuum pump with control valves/gauges, 1000 ml filter flask, water trap and connection tubing. ±Large capacity design minimises segregation effects. ±Lightweight polycarbonate construction. ±Transparent top for visual observations.Further Information:For 220-240 V AC, 50 Hz, 1 ph.SpecificationsDimensions (mm) (Outside dia x height)273 x 406 (outside dia x height)CapacityApprox. 10 ltrs, 6000 g sample weightConnectionsWater inlet valve; quick disconnect for vacuum gauge and hoseWeight (kg)3.6Power Supply220-240 V AC, 50 Hz, 1 phSpares/Consumables:Filter Flask 1000 ml (82-2350), 1 metre Red Rubber Tubing (81-3310/10), Vacuum Pump (5020 x 0076)Vacuum Pyknometer 6000 gProduct Code: 45-9300Product Standards:EN 12697-5, ASTM D2041/D2041M, AASHTO T209SpecificationsCapacityApproximately 10 ltrs, 6000 g (13.2 lbs) sample weightConstructionLightweight polycarbonate with transparent upper halfGauge2 inches (50.8 mm) diaAspiratorPlastic; 3/8 inch pipe thread (included)ConnectionsWater inlet valve; quick disconnect for vacuum gauge and hoseDimensions10-3/4 inches (273 mm) outside dia x 16 inches (406 mm) heightWeightNet 8 lbs (3.6 kg)5020 x 007645-930082-235081-0375Accessories: 1/4 inch outside diameter Plastic Tubing (45-9301/14), Drierite Desiccant (45-9315/14), Filtering Kit (45-9301)www.ele.com • email: ele@eleint.co.uk • tel: +44 (0)1525 249 200237Specific GravityAsphaltRice Test VibratorRice Test VibratorProduct Code: 45-9415/01, 45-9415/06Flash & Fire PointThere are a number of test methods using different equipment with closed or open cups. The Cleveland Flash Cup Apparatus is used to test cutback bitumen and may sometimes also be used to test penetration grade bitumen. The apparatus utilises the Open Cup test method. Note that results from different methods cannot be correlated.Cleveland Flash Cup ApparatusProduct Code: 46-3310/01Product Standards:ISO 2592 (EN 22592), BS 2000-36, ASTM D92, AASHTO T48The ELE Semi-Automatic Cleveland Open Cup Flashpoint Tester is equipped with an electrically heated cup (with a variable control to set temperature rise rate), a button operated and electrically driven sweep arm and a test flame for use on natural gas. Bench mounted, the unit is incorporated in an easy to clean Stainless Steel case.Further Information:For 220-240 V AC, 50-60 Hz, 1 ph.SpecificationsSize H x W x dia (mm)330 x 310 x 290Temperature RangeAmbient to 400°CPower (W)500 maxRamp RateVariable, manually controlledPower Supply220-240 V AC, 50-60 Hz, 1 phWeight (kg)6.5Spares/Consumables:Test Cup (46-3310/10)Cryostat (-20°C) (46-3310/11)SpecificationsMain Body Length, Arm, Operating Length (mm)13 x 64 x 58Product Standards:EN 12697-5, ASTM D2041/D2041M, AASHTO T209The Rice Test Vibrator is used with the 45-9300 6000 g Vacuum Pyknometer. Adjustable clamps hold the pyknometer securely to the base during vibration.Further Information:For 220-240 V AC, 50 Hz, 1 ph.SpecificationsDimensionsW x H x D (m)0.31 x 0.51 x 0.31Weight (kg)12Accessories:Attachment required for 6000 g Pyknometer (45-9315/10)Timer ClockProduct Code: 81-0518tel: +44 (0)1525 249 200 • email: ele@eleint.co.uk • www.ele.com238Bitumen & TarAsphaltRing & Ball ApparatusRing & Ball Apparatus BS/ENProduct Code: 46-4605Product Standards:EN 1427, BS 2000-58, ASTM D36/D36M, AASHTO T53To measure softening point with 2 shouldered pattern rings, 2 ball-centring guides and 2 balls. The apparatus has a support frame and is retained in a heat resistant container.SpecificationsWeight (kg)0.6Accessories:Electric Hotplate (46-4825/01)Laboratory Thermometer (mercury free) (82-5272) Range -10°C to +101°C x 0.2°C divisionsLaboratory Thermometer (mercury free) (82-5274) Range -10°C to +210°C x 1°C divisionsElectrical Hotplate with Integral Magnetic StirrerProduct Code: 46-4825/01Product Standards:EN 1427, BS 2000-58Utilises a rotating magnetic field to induce variable speed stirring action. A built-in regulating transformer provides fine temperature control of liquid up to a maximum temperature of +150°C. The unit is suitable for use with the Ring and Ball Apparatus.SpecificationsWeight (kg)2Power Supply220-240 V AC, 50-60 Hz, 1 phThermometerProduct Code: 82-5272Product Standards:EN 1427, BS 2000-58Mercury-free with a range of -10°C to +101°C and graduated every 0.2°C. Immersion up to 76 mm.SpecificationsTemperature Range °C-10 to +101ThermometerProduct Code: 82-5274Product Standards:EN 1427, BS 2000-58Mercury-free with a range of -10°C to +210°C and graduated every 1°C. Total immersion possible.SpecificationsTemperature Range °C-10 to +21082-527282-5274Softening PointThe test is performed in duplicate under closely controlled conditions. Water is used as the bath medium for binders with softening points below 80°C. Above this temperature glycerol is used in place of water. The softening point is a fundamental property of binders other than cutbacks and emulsions. The test is often referred to as the Ring and Ball test.www.ele.com • email: ele@eleint.co.uk • tel: +44 (0)1525 249 200239Bitumen & TarAsphaltPenetration TestSemi-Automatic PenetrometerProduct Code: 46-5295/01Product Standards:EN 1426, BS 2000-49, EN 13179-2, ASTM D5/D5M, AASHTO T49As 46-5290 but incorporates Digital Automatic Controller which releases the needle assembly. The time set is displayed by a bright, easy to read display.SpecificationsPower Supply220-240 V AC, 50-60 Hz, 1 phStandard PenetrometerProduct Code: 46-5290Product Standards:EN 1426, BS 2000-49, EN 13179-2, ASTM D5/D5M, AASHTO T49Penetration readings are quickly taken using this simple to operate apparatus. The 150 mm diameter dial is graduated in 400 divisions of 0.1 mm. Supplied without needles and penetration tins.Further Information:Model shown with sample container; not included, order separately.SpecificationsDial Indicator6 inches (150 mm) diaPlunger Weight (g)47.5Plunger ReleaseManual mechanismWeightNet 18 lbs (8.2 kg)Penetration NeedleProduct Code: 46-5340/CProduct Standards:EN 1426, BS 2000-49, EN 13179-2, ASTM D5/D5M, AASHTO T49Hardened steel, supplied with a UKAS verification certificate. For testing to BS 2000-49 and ASTM D5. (Pack contains 1 needle only).SpecificationsWeight (g)2.5Penetration NeedleProduct Code: 46-5360/10Unverified Hardened Steel46-5340/C 46-5360/10 Next >